Posts: 341
Threads: 8
Joined: Jan 2007
Reputation:
2
Posts: 377
Threads: 15
Joined: Oct 2006
Reputation:
0
Wow. That is one huge block of wood. Good luck with it. I always enjoy seeing other people's projects. Makes me feel a bit more normal..... :lol:
"A wise man learns from his mistakes, but the truly wise man learns from the mistakes of others."
Chris Boatcallie
Posts: 341
Threads: 8
Joined: Jan 2007
Reputation:
2
The whole planing through gluing took about a week. Most of the time was spent in drying. Thank goodness for big-a$$ pipe clamps. The boards had to be pulled some to get straightened out. There were no voids in the piece. The woodturner was amazed and delighted.
It took all the two of us had to load the block into the truck. We stored it upright in my foyer until turning day rolled around (about six weeks later). The block need to remain in a warm stable atmosphere so it wouldn't pull apart.
More tomorrow!
Cheryl Boeckmann
Posts: 2,716
Threads: 42
Joined: Dec 2006
Reputation:
18
Amazing! This is how I was panning to go for a shield,but...well.I have no lathe! It would have been impossible to make it by hand. Well,not impossible,and I'm not that bad a wood sculptor,but it would have been a HELL of work!
Khaire
Giannis
Giannis K. Hoplite
a.k.a.:Giannis Kadoglou
a.k.a.:Thorax
Posts: 7,668
Threads: 117
Joined: Apr 2005
Reputation:
0
Well, looks like you're about to make 30 kilos of wood shavings. What are you going to do with those? :lol:
Gotta see the next step. Will the turner cut out the inside, then the outside, or will it be done in one step? How much will this beauty set you back in coin?
Hmm. It might be possible to make something that would turn a block like that, hooked to something like a clothes dryer motor and pulley, with just a couple of bolts through the middle to start with. Fill the bolt holes with dowels when complete? I dunno. Just a thought.
M. Demetrius Abicio
(David Wills)
Saepe veritas est dura.
Posts: 341
Threads: 8
Joined: Jan 2007
Reputation:
2
Posts: 341
Threads: 8
Joined: Jan 2007
Reputation:
2
Hmmm. Don't know why the second pic is a download... Anyway, It took three of us to run the blank through the bandsaw and three of us to mount it on the lathe. Ed, the artist who turned this, had to re gear his lathe. The forces on the spindle were very high. He watched the spinning piece like a hawk. If it came off the lathe, it would have taken out the shop wall and anything/one between it. He had a pretty slow RPM on the lathe until he had removed a lot of weight. We had a cardboard pattern he measured against. It is truly a hand-turned piece.
Cheryl Boeckmann
Posts: 2,716
Threads: 42
Joined: Dec 2006
Reputation:
18
Nice...But...$800? ISn't it a bit too much? I mean,the finished priduct would have costed more than a manning shield,right?
Eagerly wating for the rest... :wink:
Khaire
Giannis
Giannis K. Hoplite
a.k.a.:Giannis Kadoglou
a.k.a.:Thorax
Posts: 341
Threads: 8
Joined: Jan 2007
Reputation:
2
Actually, I mispoke (mistyped). I'm $600 into it and looking at another $200 for leather/bronze for the interior. This is my personal challenge - so I'll finish it (in steps). If I needed a nice shield "ready-to-wear", the Manning Imperial items are definitely looking more attractive.
Cheryl Boeckmann
Posts: 341
Threads: 8
Joined: Jan 2007
Reputation:
2
Another pic. Ed turned the outside first. He later made a huge pair of calipers to hold the interior close to spec (about 1/2" thk. - 12-13mm).
Cheryl Boeckmann
Posts: 7,668
Threads: 117
Joined: Apr 2005
Reputation:
0
Funny how we (almost) all complain about the price of something, and then decide to do it ourselves, suddenly realizing why the sellers charge what they do, isn't it? I'm not being critical here. I'm amazed that you're able to find someone with the tools to do the work that doesn't want you to bring them the keys to a new car or something.
I've looked at pricey metalwork, helmets, swords, things like that and said, "Wow! That's way too much money", but now that I'm doing some metalwork, I think some of it is probably too cheap...or they're a whole lot faster than I am, which is most likely true. That realization doesn't make it any more affordable, but a lot more understandable.
M. Demetrius Abicio
(David Wills)
Saepe veritas est dura.
Posts: 2,716
Threads: 42
Joined: Dec 2006
Reputation:
18
This is excellent.Looks great! How much time does it take to form the exterior?
Giannis K. Hoplite
a.k.a.:Giannis Kadoglou
a.k.a.:Thorax
Posts: 341
Threads: 8
Joined: Jan 2007
Reputation:
2
It's hard to determine actual turning time. I would suspect around 10 hours per side. Ed said that to do it again, he would be able to do it faster. He would also have some specialist tool rests made because the interior was almost impossible to work the nearer the center he got.
Both he and I had illnesses, work, and family crises that stretched this whole phase out to two months of weekends.
Cheryl Boeckmann